1. Evi D30 Drivers For Macbook Pro
  2. Evi D30 Drivers For Macbook Air
  3. Evi D30 Drivers For Mac Os
  4. Evi D30 Drivers For Macbook

Title: EVI-D30/D31 Author: Power Mac 71 ⼀㠀 䄀嘀⁑救禍 Subject: EVI-D30/D31 Created Date: 9:44:41 AM. Sony Visca Driver EVI-D30/EVI-D31 Controller for Cameras with the Visca protocol. (example Sony EVI - D30 /31) Pan, tilt, and zoom camera with absolute or relative positioning. Synchronous or Asynchronous modes. Handles daisy-chaining and camera broadcasting.

Attach the cables required between the video encoder and the camera, then configure the video encoders settings.
Hardware connections:

  1. Connect the video from the camera to the video encoder. On the back of the EVI-D30/31 there is an area labeled “OUT”. Underneath “OUT”, one of the RCA jacks is labeled “VIDEO”. Connect a RCA cable from this to one of the video encoder’s open video in ports. You may need to use an RCA to BNC converter on the side of the cable that is being connected to the 2400/2400+.
  2. Connect the VISCA cable from the COM1 serial port on the 2400/2400+ to the VISCA IN port on the back of the EVI-D30/31.
  3. Next, configure the camera ID on the EVI-D30/31. On the back of the EVI-D30/31, above “OUT” there is an area labeled ‘CAMERA NO.’ witch you can set to 1.


Video Encoder Configuration:
Note this section of configuration is firmware version specific.
AXIS 2400/2401 firmware version 2.xx and AXIS 2400+/2401+ firmware version 3.xx:

  • Bring the web interface of the AXIS 2400/2400+ up in a browser window.
  • Click the admin button to enter the administration pages on the video encoder.
  • Click the icon labeled ‘COM1’ and change the following settings:

- Set ‘Purpose’ to ‘Pan Tilt’
- Set ‘Interface Mode’ to ‘RS232’
- Set ‘Baud Rate (bps):’ to 9600
- Set ‘Data Bits:’ to 8
- Set ‘Stop Bits:’ to 1
- Set ‘Parity Bit’ to None
- Click the ‘Save’ button

  • Next click the icon labeled ‘Pan Tilt’ located below the icon for ‘COM1’

Evi D30 Drivers For Macbook Pro

- Set ‘Drivers for Pan Tilt’ to ‘Sony EVI-G20/G21/D30/D31’
- Click ‘Save’

  • Next click the icon for the video input the EVI-D30/31 is attached to

- Set ‘Pan Tilt Serial Port’ to ‘Sony - EVI-G20/G21/D30/D31’
- Click the ‘Driver Specific Settings’ button
- A new browser window will launch to display the parameters.
- Change ‘Camera X has ID’ to ‘no 1’.

- Set the drop down box to the right of ‘no 1’ to ‘D30/D31’
- Click ‘Apply’
- Click ‘Close’

  • That will complete the PTZ setup.


AXIS 2400/2401 firmware version 1.xx:

  • Bring the web interface of the 2400 up in a browser window.
  • Click the admin button to enter the administration pages on the 2400.
  • Click the icon labeled ‘COM1’ and change the following settings:

- Set ‘Purpose’ to ‘Pan Tilt’
- Set ‘Interface Mode’ to ‘RS232’
- Set ‘Baud Rate (bps):’ to 9600
- Set ‘Data Bits:’ to 8
- Set ‘Stop Bits:’ to 1
- Set ‘Parity Bit’ to None
- Click the ‘Save’ button

Macbook
  • Next click the icon labeled ‘Pan Tilt’ located below the icon for ‘COM1’

- Set ‘Drivers for Pan Tilt’ to ‘Sony D30/D31’
- Click ‘Save’
- A new window will appear titled ‘Specific parameter for Sony D30/D31’.
- Change the ‘Camera X is connected to ID’ to ‘ID no 1’ than click 'Apply' and 'Close'.

  • Next click the icon for the video input the EVI-D30/31 is attached to

- Set ‘Pan Tilt Serial Port’ to ‘COM1 – Sony D30/D31’
- Click Save

  • That will complete the PTZ setup.


Troubleshooting:
If the EVI-D30/D31 will not PTZ then try the following:

Evi D30 Drivers For Macbook Air

Evi D30 Drivers For Mac

Evi D30 Drivers For Mac Os

- Check the VISCA cable connection to make sure it is secure
- Recheck all the parameter settings.
- Restart the video encoder and try to PTZ again.

Evi D30 Drivers For Macbook


Vote, how useful was this article to you?